Alure Craft 7000 Walk Around
Welcome to Alure Craft, where the owners are constantly looking for better ways to lead the industry.
Built in Mandurah by the van Rongen family, Alure Craft Boats were born out of years spent commercial fishing and building everything from small vessels to superyachts.
We are constantly improving the hulls and dimensions to make better sea-going boats, safer boats for clients and better boats for fishing and enjoying Australia’s incredible waterways.
Do you know a boat builder who builds each boat as it was for themselves? That’s Alure Craft.
Want to know more about the 7000 Walk Around? Send us a message below …
Our 7.6 metre 7600 is designed to a high standard.
Structural Design – ISO 12215 Small Craft Construction and scantlings, applicable to vessels less than 24m (commercial and recreational).
Stability Assessment – ISO 12217 Small Craft Stability Power +6m. Please note vessels of this size may not meet commercial stability and a best endeavours approach will be taken.
Design Category – ISO Operational Area Category B (Equivalent to NSCV Operational Area Category C – Restricted Offshore).
The hull is built “heavier” with 6mm bottoms and 5mm side, the side plate knuckle running from bow to stern to act more like a fibreglass vessel.
The knuckle becomes a “big” stiffener along the hull sides and in turn becomes the side pocket in the hull. Hull stringers or stiffeners are all 60mm x 6mm marine grade plate, not extrusion (@max of 250 centres, which make it stronger.
It’s a pleasure boat designed and built to commercial standards.
The vessel is designed with a longer waterline length for better ride and comes with high sides for both safety and comfort when fishing, as the “meat of your leg” is against the gunwale. The bait board, or work area, is designed to replicate commercial fishing setups.
Our boats are built like TANKS but don’t feel like one to drive.
✅ Measured length: 6.8 metres
✅ Beam: 2500mm
✅ Fuel: 400 litres
✅ Weight on trailer: 2.8 tonnes (fuel full)
✅ Hull bottom plate 6mm
✅ Hull Side plate 5mm
✅ Reverse Chines
✅ Hull sides knuckle (Invented by Jurien @ Alure Craft)
✅ Decks: 4mm
✅ Superstructure sides: 4mm
✅ Wheelhouse roof: 3mm
✅ Hull stringers 60 x 6mm @ max. of 250 centres
✅ Yamaha 300hp
✅ Hydraulic steering
✅ Capable of 45 knots (WOT)
✅ Stainless steel propeller
✅ Bow sprit
✅ Anchor well with hatch
✅ Electric drum anchor winch with chain and rope
✅ Rocna Anchor
✅ Am/FM Radio with speakers
✅ VHF Radio
✅ Double LED Light Bar
✅ Navigation lights
✅ Aft deck flood lights
✅ Aft deck under gunwale cockpit lights
✅ Gunwale rod holders
✅ Rocket launchers
✅ High sides
✅ Side pockets from transom door / battery box to anchor bulkhead Fwd.
✅ Custom Bait Board with Tackle Drawer and Rod Holders
✅ Fish kill tank with drain
✅ High End Commercial Grade flooring system
✅ Custom bait board with rod holders
✅ Battery box with dual batteries
✅ Deck wash pump
✅ Separate locker for fuel filters – Keeps batteries and fuel filters in separate areas as a safety feature
✅ Sink and faucet
✅ Live bait tank (40L)
✅ Transom door
✅ Custom dive ladder
✅ Marlin board
✅ Seat boxes
✅ Seats with slides
✅ Reversible seats
✅ Lockable cabin door
✅ Overhead radio console
✅ Two Bowmar hatches in wheelhouse deckhead
✅ Side window sliders
✅ 4 down lights in wheelhouse roof
✅ Electric type salt water toilet
✅ Toilet roll holder
✅ Carpet in cabin
✅ Bowmar hatch in cabin deckhead
✅ 2 down lights in cabin
✅ Bunks with storage under
✅ Bank mattresses with cushions
✅ Cray winch and tipper
TRAILER (7600 model shown):
✅ Custom drive on / off trailer – 3.5 tonnes rated
✅ Electric over hydraulic brakes with break-a-way system
✅ 70mm towing coupling
✅ Torsion 2500kg axles with all stainless-steel components
✅ Light commercial tyres – Landcruiser stud pattern
✅ 225/70 R15 tyres on Galvinised rims
✅ Braided stainless steel brake lines
✅ Brakes, callipers and hubs (stainless steel)
✅ Oil bath axle bearings
✅ LED lights with individual cable runs using waterproof connections (5 year warranty)
✅ 50mm Towing Ball
✅ Alko Winch
* Trailers are made from 5083 plate aluminium and are fully welded (another innovation from Alure Craft) – not from extrusions- deemed extra 45% tensile strength in comparison.